GasWatch 3
Status: discontinued by RKI Instruments
In November 2026, RKI announced that the GasWatch 3 is discontinued after seven years in production. New GasWatch 3 monitors are no longer available. The information below is kept as a reference for units still in service.
Parts and service continue. RKI states that replacement parts for the GasWatch 3, including sensors and filters, will remain available for many years. The parts we carry are listed under "GasWatch 3 compatible parts" below. Contact us about calibration and service.
RKI's recommended replacement is the 04 Series single-gas monitor. The closest 04 Series match for each GasWatch 3 version:
- GW-3 (O2), oxygen: OX-04 oxygen monitor, 0–40% vol (72-0018)
- GW-3 (HS), hydrogen sulfide: HS-04 H2S monitor, 0–200 ppm (73-0063)
- GW-3 (CO), carbon monoxide: CO-04 CO monitor, 0–2,000 ppm (73-0065)
- GW-3 (C-), H2-compensated CO: CO-04C CO monitor with H2 compensation (73-0067)
- GW-3 (CX), dual CO/O2: CX-04 CO/O2 monitor (73-0069)
The 04 Series is also available for ammonia (NH3), chlorine (Cl2), hydrogen cyanide (HCN), nitrogen dioxide (NO2), phosphine (PH3) and sulfur dioxide (SO2). Every version has:
- Audible, visual and vibration alarms
- A pocket-sized, IP-67 impact-, dust- and water-resistant housing
- Field-replaceable sensors and filters
- A 3-year warranty
The CO, H2S, H2-compensated CO and CO/O2 sensors used in the GasWatch 3 are the same part numbers RKI lists for the 04 Series.
General Information
The GasWatch 3 is the world’s smallest and lightest single-gas monitor. Weighing just 1.6 ounces, its compact form affords great comfort and flexibility in how you choose to wear it. It can be worn on your wrist as a watch, or clipped into your breathing zone on your lapel, hard hat or other safety equipment with its alligator clip. The 5 different GasWatch 3 models can protect you from oxygen deficiency [GW-3(O2)], exposure to carbon monoxide [GW-3(CO)] or exposure to hydrogen sulfide [GW-3(H2S)]. A hydrogen compensated model [GW-3(C-)] can protect those who work in steel mills, refineries or other environments where hydrogen is present from carbon monoxide exposure. The dual sensor model [GW-3(CX)] can simultaneously protect you from oxygen deficiency and carbon monoxide exposure. A small, field-replaceable, coin-type lithium-ion battery gives the GasWatch 3 over 4,000 hours of continuous operation. The hydrogen compensated CO can operate up to 2,500 hours, and the dual sensor CO/O2 model will get up to 2,000 hours of continuous operation. The great battery life coupled with a 3-year warranty* gives the GasWatch 3 tremendous value and a low cost of ownership.
GasWatch 3 calibration guide
Bump test the instrument before each day’s use with a known concentration of the targetgas. A bump test can be done in User Mode’s BUMP item or by applying gas inMeasuring Mode. The instrument does not need to be calibrated unless it does not pass theUser Mode bump test or does not respond appropriately, as defined by the user, inMeasuring Mode.
- To fully calibrate the sensors, you must do a fresh air adjustment (AIR CAL) and a spanadjustment (A-CAL or E-CAL).
- The GasWatch 3 can be calibrated using either A-CAL or E-CAL depending on thesetting of the E-CAL User Mode item.
- A-CAL (appears if E-CAL User Mode item is set to OFF): Apply gas for a period oftime, then press and release POWER/MODE to perform the adjustment.
- E-CAL User Mode item is set to something besides OFF): As soon asgas is applied and the reading reaches 10% of the auto calibration value, the instrumentcounts down from the number of seconds specified in the E-CAL User Mode item andautomatically performs the adjustment.
GasWatch 3 compatible parts
Replacement parts for the GasWatch 3 that we carry:
- ESR-A13P-CO carbon monoxide sensor (GW-3 CO)
- ESR-A13i-H2S hydrogen sulfide sensor (GW-3 HS)
- ESR-A1CP-CO-H H2-compensated CO sensor (GW-3 C-)
- ESR-X1DP-CX CO/O2 combination sensor (GW-3 CX)
- 81-1194 calibration adapter
- 07-0056 sensor gasket
- 21-1955 sensor retainer
- 21-1956 battery retainer
- 10-1088 retainer screw
- 13-0126 alligator clip